On 1 11:23 AM, "Cisco Developer Community Forums" wrote: In the process of nuance integration with Should we need to add nuance hostname or IP addressīefore configuring with CVP. Subject: Re: New Message from GEOFFREY THOMPSON in Customer Voice Portal (CVP) - Gen To respond to this post, please click the following link: GEOFFREY THOMPSON has created a new message in the forum "General Discussion - All Versions": To: New Message from GEOFFREY THOMPSON in Customer Voice Portal (CVP) - General Discussion - All Versions: RE: New Message from Phani Venigalla in Customer Voice Portal (CVP) - Gener Please be wary of this.įrom: Cisco Developer Community Forums You send one response and you will get back 10 questions in return. Subject: RE: New Message from GEOFFREY THOMPSON in Customer Voice Portal (CVP) - Gen (No response is required from you for this simple advice. Are you doing H.323? If no, ignore that section.Are you doing any microapps? If no, ignore that section.Ignore the rest and come back to it later when you have the basics working. Replied by: GEOFFREY THOMPSON on 13-04-2012 01:23:05 PMĬVP has lots of options, as I am sure you know.Īs a beginner, concentrate on what you have and only on what you need to know for those options. With CVP VXML apps, the only setting of importance is the RTSP.ĭO debug on mrcp on the gateway to check. If you don’t have a CSS, why ask about it? Well I used Microapps to Trigger CVP application from ICM, The DN has configured on Gateway.
Here these ip addresses or host name belongs to TTS servers right? Is that necessary to go with IP addresses in the following statement or we can mention Host name instead of Ip adderesses. Replied by: Phani Venigalla on 13-04-2012 01:16:16 PMĪctually the config guide has CSS so i have cinfused. I have configured in NSSConfig at NSS server But I am confused at CVP End. I have two nuance vocalizer servers: Server1 and Server 2 as back up.which i need to integrate with CVP. Subject: RE: New Message from Phani Venigalla in Customer Voice Portal (CVP) - Gener I am little confused about CSS configurationĬontent ASR add service asr1 add service asr2 primarySorryServer asr3 protocol tcp port 554 vip address 10.1.3.12content TTS add service tts1 add service tts2 primarySorryServer tts3 protocol tcp port 554 vip address 10.1.3.13 What else we need to do on CVP side to integrate with Nunace. On the other hand, based on your other numerous other posts, I could interpret your request as one for step-by-step guidance on setting up a system with CVP and Nuance, and that is clearly not what this forum should be used for. If that is the case, the document you should start with is the Configuration and Administration Guide for CVP, located here: On the one hand, I could interpret your request as a request for a link to standard documentation. Your post is a pretty open-ended request with little to no information on what your environment is and what you're really looking for. With all due respect, and I know I'm not the first to express this concern to you, this forum is meant to be an information sharing resource that may also provide "support" in the context of shared experience and ideas. I don't know why i am not getting any help. I am stll waiting somebody can reply on my query. Subject: RE: CVP With Nuance TTS Vocalizer What parameters need to configure to intgrate with CVP. I have installed Nuance TTS vocalizer and Seechserver. Var g_ssSourceNodeId = "ncom_bus_prod_ccs_inbd_ssa_voc" Ĭufon.replace('#ncom_maincontent h1', ) Ĭufon.replace('a.This document was generated from CDN threadĬreated by: Phani Venigalla on 11-04-2012 04:50:10 PM G_navNode_Path = 'ncom_bus_prod_ccs_inbd_ssa_voc' G_navNode_Path = 'ncom_bus_sol_cccc_ccss_slfsrv' G_navNode_Path = 'ncom_bus_sol_cccc_inboundsol' G_navNode_Path = 'cccc_solutions_services' G_navNode_Path = 'ncom_bus_sol_custservic'